Skip to content
Free Shipping on most orders over $150.00. Buy now, pay later with ShopPay                    
Free Shipping on most orders over $150.00. Buy now, pay later with ShopPay                    

New 7.3L Powerstroke Cylinder Heads (Pair), Machined In House 1994 to 2003

Original price $1,550.00 - Original price $1,850.00
Original price
$1,550.00
$1,550.00 - $1,850.00
Current price $1,550.00
Description

Brand new 7.3 cylinder heads. Price is for the pair. Both heads, ready to bolt on. New castings that have never been installed in an engine or heat cycled. No core to send back and no core charge. What you order is what you keep.


Better Than the Day It Left the Factory

The factory 7.3 head was built to a price. Ours is built to last. Every head starts as a brand new casting, then goes through our Full Works process at Tru Cylinder Head and Machine, our own machine shop in Jefferson City, Tennessee. Same crew that has handled our machine work for eight years, same equipment, one standard: if we would not bolt it on our own truck, it does not leave the building.

This is not a head pulled off a shelf and repainted, and it is not something shipped out by a contract shop you will never talk to. It is the best 7.3 head we know how to build, and we put our name on it.

O Ringed or Standard. Your Call.

Choose O ringed and we machine a receiver groove into the deck and set stainless wire in it. That wire drives clamping pressure into the head gasket and locks it in place, so it cannot lift under boost, load or heat. For 7.3 trucks with studs, bigger injectors, a turbo upgrade or a heavy trailer behind them.

Choose standard for a stock or lightly modified truck. Same casting prep, same machine work, same inspection, set up for stock cylinder pressure.

Built for How You Actually Use the Truck:

  • Towing heavy: gooseneck, bumper pull, hotshot, anything that lays into the EGTs on a grade
  • Street trucks running a tune: where a tired factory head is the first thing to give up
  • Strip and sled pull: high cylinder pressure, repeated heat cycles, no room for a lifting head
  • Work trucks and daily drivers that have to start every morning and cannot sit in a shop

What Goes Into Every Head:

  • New injector cups. Leaking cups are the number one cause of fuel in the coolant on a 7.3. Not on ours.
  • New intake valves.
  • Crack checked and pressure tested before any machine work starts
  • Valve guides and seats cut true to our spec
  • New valve seals to keep oil out of the combustion chamber
  • Complete valve job, every valve lapped and checked for seal
  • Deck surfaced flat on precision equipment for a gasket that seals the first time
  • Optional O ringing for maximum clamping pressure under high cylinder pressure
  • Final inspection by the people who did the work

A head set up right does more than seal. True seats and a proper valve job mean better airflow and cleaner combustion, which shows up as more power, lower EGTs and better fuel economy.

Why Ours Are Different

Most heads sold online are machined by somebody else and sold under another name. Ours are cut in our own building, on our own equipment, by our own people, and we will tell you the specs we hold. Call and ask. Try that anywhere else.

Priced as a pair. If one head let go, the other one lived through the same heat cycles. Doing one and reusing the other is how trucks end up back in the bay.

Built for guys towing heavy, running a tune, or done doing the same job twice. This is the last head job that truck will need.


FAQ

Are these new or remanufactured?
New. Every head we sell starts as a brand new casting that has never been installed or heat cycled, then goes through our Full Works machine process before it ships.

Do I need to send in a core?
No. No core charge, no core return, nothing to ship back.

Are these better than factory?
Yes. Seats and guides are cut to our spec, every valve is lapped, the deck is surfaced flat, and you can add O ringing, which no factory head has. Every one is inspected by the people who built it.

Should I O ring them?
If the truck is tuned, towing heavy, or making more boost than stock, yes. It is the single best thing you can do to keep a head gasket from lifting.

Will these heads fix my head gasket problem?
Only if the engine is studded and you fix what caused the failure, usually an overheat. Fresh heads on an engine with a cooling problem will fail again. Call us before you buy and we will talk through what you are actually chasing.

How does shipping work?
Heads ship nationwide, with freight quoted per order. In East Tennessee our courier delivers to your shop from Knoxville to Greeneville.

Do you sell to repair shops?
Yes. Shops and fleets can open a wholesale account. Call 865.640.2097.

Rebuilding the whole engine? Pair these with our 7.3 short block, built in house with an OEM overhaul kit, oil cooler and LPOP.

Questions? Call Tru Cylinder Head and Machine at 865.548.8520 or Powerhouse Diesel at 865.640.2097.

Warranty

You may also like

  • Ford Motorcraft RTV Silicone Sealant 5fl Oz. TA-31

    Ford
    Original price $42.60 - Original price $42.60
    Original price
    $42.60
    $42.60 - $42.60
    Current price $42.60

    Motorcraft TA-31 is the RTV silicone Ford uses from the factory. On Powerstroke engines it is the sealant called for on oil pans and other formed i...

    View full details
    Original price $42.60 - Original price $42.60
    Original price
    $42.60
    $42.60 - $42.60
    Current price $42.60
  • Diesel Technology High Voltage IDM | 1994 to 2003 7.3 Powerstroke

    Diesel Tech
    Original price $700.00 - Original price $700.00
    Original price
    $700.00
    $700.00 - $700.00
    Current price $700.00

    Snappier throttle response from a rebuilt, upgraded injector driver module. On top of the normal rebuild, Diesel Technology raises output to the in...

    View full details
    Original price $700.00 - Original price $700.00
    Original price
    $700.00
    $700.00 - $700.00
    Current price $700.00
  • Diesel Technology Rebuilt PCM | 1994 to 2003 7.3 Powerstroke

    Diesel Tech
    Original price $705.00 - Original price $765.00
    Original price
    $705.00
    $705.00 - $765.00
    Current price $705.00

    A rebuilt PCM for the 1994 to 2003 7.3 Powerstroke from Diesel Technology, for when the main engine and transmission computer finally gives out.Que...

    View full details
    Original price $705.00 - Original price $765.00
    Original price
    $705.00
    $705.00 - $765.00
    Current price $705.00
  • RCD Hydraulic Lifter Set | 6.0, 6.4 and 7.3 Powerstroke

    RCD Performance
    Original price $249.00 - Original price $599.99
    Original price
    $249.00
    $249.00 - $599.99
    Current price $249.00

    Hydraulic lifters for the 6.0, 6.4 and 7.3 Powerstroke in three versions: US made Hylift Johnson HD, an economy heavy duty design, or OEM Delphi/Ea...

    View full details
    Original price $249.00 - Original price $599.99
    Original price
    $249.00
    $249.00 - $599.99
    Current price $249.00
  • CNC Fab HPOP Lines with HPx | Early 1999 to 2003 7.3 Powerstroke

    Cnc
    Original price $233.95 - Original price $233.95
    Original price
    $233.95
    $233.95 - $233.95
    Current price $233.95

    Replace the leaky factory HPOP lines with STC fittings on early 1999 to 2003 7.3 Powerstrokes. The kit includes 3 hoses and the fittings to elimina...

    View full details
    Original price $233.95 - Original price $233.95
    Original price
    $233.95
    $233.95 - $233.95
    Current price $233.95