Skip to content
Free Shipping on most orders over $150.00. Buy now, pay later with ShopPay                    
Free Shipping on most orders over $150.00. Buy now, pay later with ShopPay                    

New 6.6L Duramax Cylinder Heads (Pair), New Casting Machined In House LB7 to LML

Part#:

TRU-FW-DMAX-STD
Original price $1,900.00 - Original price $2,300.00
Original price
$1,900.00
$1,900.00 - $2,300.00
Current price $1,900.00
Description

Brand new Duramax cylinder heads. Price is for the pair. Both heads, ready to bolt on. New castings that have never been installed in an engine or heat cycled. No core to send back and no core charge. What you order is what you keep.


Better Than the Day It Left the Factory

The factory Duramax head was built to a price. Ours is built to last. Every head starts as a brand new casting, then goes through our Full Works process at Tru Cylinder Head and Machine, our own machine shop in Jefferson City, Tennessee. Same crew that has handled our machine work for eight years, same equipment, one standard: if we would not bolt it on our own truck, it does not leave the building.

This is not a head pulled off a shelf and repainted, and it is not something shipped out by a contract shop you will never talk to. It is the best Duramax head we know how to build, and we put our name on it.

O Ringed or Standard. Your Call.

Choose O ringed and we machine a receiver groove into the deck and set stainless wire in it. That wire drives clamping pressure into the head gasket and locks it in place, so it cannot lift under boost, load or heat. Pick this for any Duramax running a tune, towing heavy or making serious boost.

Choose standard for a stock or lightly modified truck. Same casting prep, same machine work, same inspection, set up for stock cylinder pressure.

Built for How You Actually Use the Truck:

  • Towing heavy: gooseneck, bumper pull, hotshot, anything that lays into the EGTs on a grade
  • Street trucks running a tune: where the factory head gasket is the weak link
  • Strip and sled pull: high cylinder pressure, repeated heat cycles, no room for a lifting head
  • Work trucks and daily drivers that have to start every morning and cannot sit in a shop

What Goes Into Every Head:

  • Crack checked and pressure tested before any machine work starts
  • Valve guides and seats cut true to our spec
  • New valve seals to keep oil out of the combustion chamber
  • Complete valve job, every valve lapped and checked for seal
  • Deck surfaced flat on precision equipment for a gasket that seals the first time
  • Optional O ringing for maximum clamping pressure under high cylinder pressure
  • Final inspection by the people who did the work

A head set up right does more than seal. True seats and a proper valve job mean better airflow and cleaner combustion, which shows up as more power, lower EGTs and better fuel economy.

Why Ours Are Different

Most heads sold online are machined by somebody else and sold under another name. Ours are cut in our own building, on our own equipment, by our own people, and we will tell you the specs we hold. Call and ask. Try that anywhere else.

Priced as a pair. If one head let go, the other one lived through the same heat cycles. Doing one and reusing the other is how trucks end up back in the bay.

Built for guys towing heavy, running a tune, or done doing the same job twice. This is the last head job that truck will need.


FAQ

Are these new or remanufactured?
New. Every head we sell starts as a brand new casting that has never been installed or heat cycled, then goes through our Full Works machine process before it ships.

Do I need to send in a core?
No. No core charge, no core return, nothing to ship back.

Are these better than factory?
Yes. Seats and guides are cut to our spec, every valve is lapped, the deck is surfaced flat, and you can add O ringing, which no factory head has. Every one is inspected by the people who built it.

Should I O ring them?
If the truck is tuned, towing heavy, or making more boost than stock, yes. It is the single best thing you can do to keep a head gasket from lifting.

Will these heads fix my head gasket problem?
Only if the engine is studded and you fix what caused the failure, usually an overheat. Fresh heads on an engine with a cooling problem will fail again. Call us before you buy and we will talk through what you are actually chasing.

How does shipping work?
Heads ship nationwide, with freight quoted per order. In East Tennessee our courier delivers to your shop from Knoxville to Greeneville.

Do you sell to repair shops?
Yes. Shops and fleets can open a wholesale account. Call 865.640.2097.

Doing the bottom end too? See our Duramax short block with a Compstar crankshaft and HX main bearings.

Questions? Call Tru Cylinder Head and Machine at 865.548.8520 or Powerhouse Diesel at 865.640.2097.

Warranty

You may also like

  • Fleece Performance 01-17 GM Duramax Billet Coolant Block Off Plate

    Fleece Performance
    Original price $0.00 - Original price $0.00
    Original price $0.00
    $55.00
    $55.00 - $55.00
    Current price $55.00

    Fleece Performance Billet Coolant Block Off Plate Fits 2001-2017 GM 6.6L Duramax A direct replacement for the factory coolant crossover on the Dura...

    View full details
    Original price $0.00 - Original price $0.00
    Original price $0.00
    $55.00
    $55.00 - $55.00
    Current price $55.00
  • Wehrli 01-16 Chevrolet 6.6L LB7/LLY/LBZ/LMM/LML Duramax Up Pipe Bolt Kit

    Wehrli
    Original price $0.00 - Original price $0.00
    Original price $0.00
    $36.86
    $36.86 - $36.86
    Current price $36.86

    Wehrli Model WCF100240 ARP Bolt kit for 2001-2016 Duramax Up Pipes or LB7 Turbo Down pipe. 6 Washers and Bolts for installing 1 up pipe. Includes A...

    View full details
    Original price $0.00 - Original price $0.00
    Original price $0.00
    $36.86
    $36.86 - $36.86
    Current price $36.86
  • XDP Mass Air Flow (MAF) Sensor 2001-2007 GM 6.6L Duramax LB7/LLY/LBZ XD1024

    XDP
    Original price $83.95 - Original price $83.95
    Original price
    $83.95
    $83.95 - $83.95
    Current price $83.95

    XDP Model XD1024The XDP Mass Air Flow (MAF) Sensor XD1024 is an OE-style, direct-fit replacement the factory MAF sensor on your Chevy or GMC 6.6L D...

    View full details
    Original price $83.95 - Original price $83.95
    Original price
    $83.95
    $83.95 - $83.95
    Current price $83.95
  • Mishimoto 01-21 Silverado Sierra Express Savana Duramax 6.6L Low Temp Thermostat Set

    Mishimoto
    Original price $110.00
    Original price $110.00 - Original price $110.00
    Original price $110.00
    Current price $99.95
    $99.95 - $99.95
    Current price $99.95

    Mishimoto 01-21 Silverado Sierra Express Savana Duramax 6.6L Low Temp Thermostat Set Fits 2001-2021 Chevrolet/GMC 6.6L Duramax (see fitment char...

    View full details
    Original price $110.00
    Original price $110.00 - Original price $110.00
    Original price $110.00
    Current price $99.95
    $99.95 - $99.95
    Current price $99.95
    Save 9% Save %
  • XDP Harmonic Balancer Bolt XD628

    XDP
    Original price $24.95 - Original price $24.95
    Original price
    $24.95
    $24.95 - $24.95
    Current price $24.95

    XDP Harmonic Balancer Bolt XD628. Sold and shipped by Powerhouse Diesel, a diesel repair and performance shop in Knoxville, TN. Part number: XD628...

    View full details
    Original price $24.95 - Original price $24.95
    Original price
    $24.95
    $24.95 - $24.95
    Current price $24.95